Monte Flashing
***Note It is not recommended to flash any phone if you are not a technician nor have the proper equipment or training***
Step 1 You must follow this step!!!
—————————————–Set Up Your Computer—————————————————-
1. Install Kies on your computer and make sure it will communicate with your phone, or install only the driver pack.
2. Disconnect your phone and Close NPS.
3. Click “Start” or the Windows logo on the bottom left of your computer screen and click in the search/run box and type msconfig.
4. Select the tab marked “Start Up” and click “disable all” and click ok.
5. Restart the computer and you are ready to flash.
DO NOT! run NPS or Kies again until you have successfully flashed your phone! After you have successfully flashed your phone, you must reset the Windows setting back to there original and restart your computer.
————————————-Now continue with the flash————————————————
***Warning!***
Make sure your phone dose not have sim lock or net lock before you try and flash. Type *#7465625# and make sure the SIMLOCK and NETWORKLOCK is OFF, if it is ON you MUST Unlock it or you will freeze your phone! Here is fast and trusted way! Network lock is not as big of risk as simlock, you have a 50/50 chance of bricking your phone if you flash with it on. You have a 100% chance of a brick if the simlock is on. Trust me, members make that mistake every day.
First thing to always remember, is BACK UP YOUR PHONE, Pictures,wallpapers,music, and any contacts you have saved on your phone. I am not responsible for any damage to you, your phone, computer, or lost of data in this process. This is a guideline intended for professional technicians.
USE AT YOUR OWN RISK!!!
What you will need:
Check list:
1. USB cable that came with your phone.
2. Kies or Drivers installed
3. MultiLoader
4. New firmware
—————————–Now you are ready to begin———————————–
1. Make sure Samsung PC Studio is installed and communicates with your phone. And u 7/28/10 ???s??a? g?????
—————————–Now you are ready to begin———————————–
1. Make sure Samsung PC Studio is installed and communicates with your phone. And unpack the firmware in a folder you can easily find it.
2. Remove the Sim and MicroSD from your phone and replace the battery.
3. MAKE SURE THE PHONE IS OFF AND NOT CONNECTED TO THE COMPUTER.
4. Hold down the “Volume -” button on the left or right side differs, and the “Camera” button on the right, then press the “Power” button = all three buttons need to be pressed together. Your phone should start up into a red\blue on black download screen.)
5. Now run MultiLoader
6. Plug the phone up to the computer.
———————————Multiloader Steps——————————————
1. Select the radio button BRCM2153 (for S5620 etc…) Wave S8500 use LSI6410
2. Select Boot Change
3. Full Download
4. Master rom
Now Select these files in this order, you will have to switch between the contained directories as you load file.
5. Boot
6. Amss
7. Apps
8. Rsrc1
9. Rsrc2(Low) (Warning! Do not use Rsrc2 (Mid) your phone may not restart!!!)
10. Factory FS file.
11. CSC (remember this is in a separate folder)
12. SHP
13. SPP
14. PFS 7/28/10 ???s??a? g?????
***FOTA and ETC fields are left blank.****
15. Click the Port Search button, it will find your phone and show the com port is ready.
16. Click the download button and be patient, this will only take a few minutes to complete.
17. When it’s finished, it will show “ok complete”.
*** NOTE If yours does not restart at this point, take out the battery a few seconds then reinsert it. NOTE ***
18. Unplug the phone from the USB cable, reinstall the sim and SD card.
19. Now with every thing is complete, You can perform a hard reset by typing *2767*3855# into the hand set (but not necessary.)
20. When the phone resets type *#1234# into your handset to check your new firmware ver.
***NOTE!***
If your phone fails the flash for any reason, DO NOT TRY AND RESTART IT!!!!! Restart the computer and try the flash again! YES YOU MUST RESTART THE COMPUTER AND FOLLOW MY GUIDE CLOSE!
Once you have completed the download, you may want to use the pre configuration function, only if you are using firmware for your region.
Preconfiguration *#27236*#
click here to download step by step guidlines in picture....<must download> it'll help you sure.....
Step By Step Guidlines Based on XEJE1 Firmware...
